The Foundation of Plumbing Skills When Installing a Bathtub
The Foundation of Plumbing Skills When Installing a Bathtub
Blog Article
Just how do you feel in regards to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?

Mounting a tub isn't specifically rocket science, however it does require solid plumbing, woodworking, and also in some cases, tiling skills. Changing an old bathtub with a new one is additionally a moderately difficult task. If the old bathtub is conveniently available, the job can move rapidly; if you need to open a wall surface to eliminate the old bathtub and position the new bath tub, the task is a lot harder. In either case, the project is within a home handyman's abilities, although you will need a helper to vacate the old bathtub and set in the new one. See to it you have actually certified on your own for the work and also fit attempting it. Instead of working with a professional to take control of a halfway-completed job, it is better to think about employing one prior to you begin. Chances are you might require a professional plumber to make tube connections.
This article will aid you mount a brand-new bath tub in your shower room if you have actually currently acquired a new tub and also don't require to alter the arrangement of your previous water pipes.
Your tools as well as material list must consist of the following:
Preparing for the Installment
Firstly, the supporting structure supplied with the bath ought to be fitted (if called for) according to the supplier's directions. Next, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is essential to make certain that if the tap features a plastic washer, it is fitted in between the bath and also the faucets. On a plastic bathroom, it is also sensible to fit a sustaining plate under the faucets system to avoid stress on the tub.
Fit the adaptable faucet ports to the bottom of the two faucets using 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet via the hole in the bathroom. Use the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make certain you make use of all of the supplied washers.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bathroom need to currently be ready to be fitted in its last placement.
Removing Old Touches
If you require to change old taps with brand-new ones as a part of your installment, then the first thing you should do is disconnect the water supply. After doing so, switch on the taps to drain any water staying in the system. The procedure of getting rid of the existing taps can be fairly troublesome due to the limited access that is frequently the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipes to the faucets. Have a cloth prepared for the remaining water that will certainly come from the pipelines. As soon as the supply pipes have actually been gotten rid of, make use of the same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary taps from turning throughout this process. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will have to be cleaned up of any old securing substance.
Prior to proceeding to fit the brand-new taps, contrast the pipeline links on the old faucets to the brand-new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the brand-new taps to fit.
Setting up the Tub
Making use of both wood boards under its feet, put the bathtub in the called for placement. The wood boards are helpful in uniformly spreading out the weight of the bath tub over the location of the boards rather than concentrating all the weight onto 4 tiny factors.
The next objective is to make certain that the bathtub is leveled all round. This can be achieved by checking the spirit level as well as changing the feet on the tub up until the spirit level reads degree.
To mount faucets, fit the bottom of the furthest versatile faucet port to the ideal supply pipe by making a compression join; then do the same for the various other faucet.
Switch on the water system and also check all joints and also new pipework for leaks as well as tighten them if essential. Load the tub and likewise check the overflow outlet and also the normal electrical outlet for leakages.
Lastly, fix the bathroom paneling as defined in the producer's user's manual. Tiling as well as securing around the tub needs to wait up until the tub has been utilized a minimum of when as this will certainly settle it into its last placement.
Suitable New Taps
If the tails of the new taps are plastic, after that you will certainly require a plastic adapter to stop damages to the thread. One end of the adapter fits on the plastic tail of the tap and the various other end gives a link to the existent supply pipelines.
If you need to fit a monobloc, then you will require minimizing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, place the faucet in the installing hole in the bath/basin making certain that the washers are in place in between the tap and also the sink. Protect the faucet in place with the manufacturer offered backnut. As soon as the tap is safely in place, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with normal faucet adapters. The former kind should be attached to the tap ends first, tightening up just by hand. The supply pipes can later be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the area where the bath satisfies the ceramic tile, it is necessary to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate enough to fracture a stiff seal, creating the water to pass through the wall between the bathroom and the tiling, causing difficulties with wetness as well as feasible leaks to the ceiling below.
You can choose from a selection of coloured sealers to assimilate your fixtures and also fittings. They are offered in tubes as well as cartridges, and also can sealing voids approximately a width of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with twists of soaked newspaper or soft rope. Bear in mind to constantly fill the bathtub with water before securing, to enable the movement experienced when the tub remains in use. The sealer can crack rather early if you do not take into consideration this movement before sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also conveniently offered on the market. It is suggested to fit the ceramic tiles making use of waterproof or water-proof sticky and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

I came across that entry on How to Install a Bathtub when doing research the web. Those who enjoyed our blog entry plz be sure to pass it around. Thanks for going through it.
Expertise on line! Report this page